Why does my paintball gun leak air




















When you screw in a paintball gun gas tank and find that there is a significant amount of air leaking around the air source adapter ASA fitting, the problem invariably comes from a damaged O-ring. Fix this problem by removing the existing O-ring size and replace it with a new one. When air leaks out of the front of the gun below the barrel, the most common reason is that there is a bad O-ring on the front volumizer. This problem is relatively common Spyder-style paintball guns.

Simply unscrew the volumizer and replace the O-ring on the volumizer, put a thin layer of oil or grease on the O-ring, and then replace the volumizer. When air is leaking down the barrel of a paintball gun, the repair is often a little more difficult, though there is a potential short-term fix. You can try to fix this problem by putting a few drops of oil into the ASA Air Source Adapter of the gun and then screw in the tank and check to see if the problem is fixed. Be aware, though, that this fix will typically only last for a short period of time.

If the quick fix fails, the problem most likely is caused by a worn cup seal. A number of different problems may prevent a paintball gun from recocking. Address this issue by first trying to solve the problem with the simplest solution and building up to more complicated ones.

The simplest explanation is that the air tank is empty, and the obvious solution is to replace it with a filled tank. If previous paintballs were broken inside the chamber but were not properly cleaned, then the hammer and bolt may be gummed up and unable to slide correctly. You can fix this by cleaning out the chamber and making sure that all the internals are properly lubricated.

Paintball guns may also fail to recock when there is inadequate pressure on the hammer. You can increase the tension on the hammer. On Spyder-style guns, the adjustment is on the back; on Tippmans, it is on the side. If increasing tension doesn't solve the problem, you may need to replace the gun's hammer spring. Sporting goods stores will also sell CO2 tanks or refill them for you. Leaking is a fairly common problem experienced by users with CO2-powered paintball guns. With many pieces and accessories in a paintball gun, there are many crevices and areas that could be lacking the proper seal.

This problem can typically be fixed with simple adjustments and replacements, which should be tried first before taking more drastic measures. O-rings are found throughout paintball guns as a seal to prevent air from leaking out of the gun. They allow the air to build-up to the pressure needed to fire the gel capsule from the gun. There is an O-ring where the tank of CO2 attaches to the gun. This ring needs to be attached properly and intact for air and CO2 not to leak out of the paintball gun.

This ring is attached to the nozzle of the CO2 tank and is crucial to the proper fit and seal between the tank and the weapon. One of the main causes of CO2 leakage is a problem with the O-ring. O-rings are located in multiple locations on a paintball gun. The two most common areas where you can experience leaks are on the front of the gun and down the barrel of the gun.

The front of the gun is prone to leak if the O-ring is not functioning on the front volumizer extra air chamber for higher firing rates and drop off. The barrel is related to the air source adapter. The CO2 tank needs to fit snuggly into the gun to allow for proper transfer of gas and functional firing. The air source adapter ASA is a threaded port entrance for the CO2 tank to fit into your paintball gun.

Leaking can occur when the CO2 tank does not fit properly into the air source adapter. This can be caused by a faulty O-ring on the tank for any number of reasons mentioned in the previous section, or a more complicated issue with other accessory items. There is a pin in an ASA that pushes down on the tank valve to allow pressure into the paintball gun. Lack of care in handling the gun and removal of the CO2 tank may lead to damages to this pin, threading within the ASA, and the O-ring.

If replacements are made and the leaking does not stop, this suggests there is a problem with the cup seal. With extended use, the cup seal down the barrel, which also assists in sealing air, can cause leaking down the barrel of the gun. Damages to the threading on either the ASA or O-ring will not allow for the two mechanisms to properly fit into one another. With increased force, these threads can be stripped, and increased friction can create pockets where CO2 can leak out.

Always be mindful and careful when screwing in your tank to the ASA as these damages lead to leaking. Taking care of your gun with routine actions will eliminate leaking risks. If you notice CO2 leaks on your paintball gun, the damage has most likely already occurred. We know the main causes associated with leaks now O-rings, cup seals, and air source adapters and these areas should be checked for wear and tear.

You will most likely have to replace them to prevent future leaking issues. The O-ring is one of the main culprits in CO2 leakage as we have discussed. Once the O-ring is clearly broken or damaged, it must be replaced.

Having a couple of extra O-rings on hand is a good idea so you can quickly change it out once you see any damages. These are typically sold in a large pack with a variety of sizes and variations. There are some considerations you should make when choosing O-ring replacements:. To replace the O-ring, you can cut it or pull it from the tank using some form of sharp object. It is crucial that you are meticulous and careful in this process as the sharp object you use could scratch the metal on the tank leading to more problems on your hands.

You can then put the replacement O-ring on the tip of the tank nozzle or volumizer depending on location. When replacing the O-ring, make sure you are using ones that are recommended by the manufacturer of your paintball gun. This will ensure that they are the proper size and fit for the specific gun and tank you use. After reading this article on how to fix a paintball gun air leak , we believe that you will be able to easily identify and deal with the leaks by yourself. Truth is that the accessory will at some point develop leaks.

And due to this, the gun will not operate optimally meaning that you or any other users will not have fun.

While you can take it to a professional for fixing, doing it yourself is not only cheaper but also giving you a sense of pride. Also, it will save time and allow you to get back to the fun.

Following the right technique is key to ensuring the leak is fully dealt with. Table of Contents. What May Cause the Gun to Leak? Air leaks are not something odd when you own the accessory. In fact, you will deal with leaks quite often. The main reasons for a leak include the following:. If you want to read the review of the best paintball gun under check out this article. This not only saves you time and effort but also ensures you deal with the problem completely and get it right the first time.

At times, there may be more than one leak and this may mostly occur after an accident or poor handling. The following are the key ways of identifying a leak:. For instance, a worn o-ring requires a new one whereas a cracked shell needs to be bonded with strong glue.

If it is an O-ring, you should replace with a new O-ring of the same type. If it is the adapter, tightening it with a wrench may eliminate the problem. If not, then you can first wrap some tape on the thread and then tighten it.



0コメント

  • 1000 / 1000